2b0e95780
Denys Vlasenko
2009-06-17
Subject
examples/udhcp/udhcpd.conf: update
Binary
No binary (build failed)
Architecture & Compiler Flags
—
Build Log
(log yok)
Commit Diff GitHub →
examples/udhcp/udhcpd.conf+31 -64
| @@ -1,88 +1,59 @@ | |
| # Sample udhcpd configuration file (/etc/udhcpd.conf) | |
| + | # Values shown are defaults |
| # The start and end of the IP lease block | |
| - | |
| - | start 192.168.0.20 #default: 192.168.0.20 |
| - | end 192.168.0.254 #default: 192.168.0.254 |
| - | |
| + | start 192.168.0.20 |
| + | end 192.168.0.254 |
| # The interface that udhcpd will use | |
| + | interface eth0 |
| - | interface eth0 #default: eth0 |
| - | |
| - | |
| - | # The maximim number of leases (includes addressesd reserved |
| - | # by OFFER's, DECLINE's, and ARP conficts |
| - | |
| - | #max_leases 254 #default: 254 |
| - | |
| - | |
| - | # If remaining is true (default), udhcpd will store the time |
| - | # remaining for each lease in the udhcpd leases file. This is |
| - | # for embedded systems that cannot keep time between reboots. |
| - | # If you set remaining to no, the absolute time that the lease |
| - | # expires at will be stored in the dhcpd.leases file. |
| - | |
| - | #remaining yes #default: yes |
| - | |
| + | # The maximim number of leases (includes addresses reserved |
| + | # by OFFER's, DECLINE's, and ARP conficts). Will be corrected |
| + | # if it's bigger than IP lease block, but it ok to make it |
| + | # smaller than lease block. |
| + | #max_leases 254 |
| # The time period at which udhcpd will write out a dhcpd.leases | |
| # file. If this is 0, udhcpd will never automatically write a | |
| - | # lease file. (specified in seconds) |
| - | |
| - | #auto_time 7200 #default: 7200 (2 hours) |
| - | |
| - | |
| - | # The amount of time that an IP will be reserved (leased) for if a |
| - | # DHCP decline message is received (seconds). |
| - | |
| - | #decline_time 3600 #default: 3600 (1 hour) |
| - | |
| - | |
| - | # The amount of time that an IP will be reserved (leased) for if an |
| - | # ARP conflct occurs. (seconds |
| + | # lease file. Specified in seconds. |
| + | #auto_time 7200 |
| - | #conflict_time 3600 #default: 3600 (1 hour) |
| + | # The amount of time that an IP will be reserved (leased to nobody) |
| + | # if a DHCP decline message is received (seconds). |
| + | #decline_time 3600 |
| + | # The amount of time that an IP will be reserved |
| + | # if an ARP conflct occurs (seconds). |
| + | #conflict_time 3600 |
| - | # How long an offered address is reserved (leased) in seconds |
| - | |
| - | #offer_time 60 #default: 60 (1 minute) |
| - | |
| - | # If a lease to be given is below this value, the full lease time is |
| - | # instead used (seconds). |
| - | |
| - | #min_lease 60 #defult: 60 |
| + | # How long an offered address is reserved (seconds). |
| + | #offer_time 60 |
| + | # If client asks for lease below this value, it will be rounded up |
| + | # to this value (seconds). |
| + | #min_lease 60 |
| # The location of the leases file | |
| - | |
| - | #lease_file /var/lib/misc/udhcpd.leases #defualt: /var/lib/misc/udhcpd.leases |
| + | #lease_file /var/lib/misc/udhcpd.leases |
| # The location of the pid file | |
| - | #pidfile /var/run/udhcpd.pid #default: /var/run/udhcpd.pid |
| + | #pidfile /var/run/udhcpd.pid |
| # Everytime udhcpd writes a leases file, the below script will be called. | |
| - | # Useful for writing the lease file to flash every few hours. |
| - | |
| - | #notify_file #default: (no script) |
| - | |
| - | #notify_file dumpleases # <--- useful for debugging |
| - | |
| - | # The following are bootp specific options, setable by udhcpd. |
| + | #notify_file # default: no script |
| + | #notify_file dumpleases # useful for debugging |
| + | # The following are bootp specific options, settable by udhcpd. |
| #siaddr 192.168.0.22 #default: 0.0.0.0 | |
| - | |
| - | #sname zorak #default: (none) |
| - | |
| - | #boot_file /var/nfs_root #default: (none) |
| + | #sname zorak #default: none |
| + | #boot_file /var/nfs_root #default: none |
| # The remainer of options are DHCP options and can be specifed with the | |
| # keyword 'opt' or 'option'. If an option can take multiple items, such | |
| # as the dns option, they can be listed on the same line, or multiple | |
| # lines. The only option with a default is 'lease'. | |
| - | |
| - | #Examles |
| + | # Examples: |
| opt dns 192.168.10.2 192.168.10.10 | |
| option subnet 255.255.255.0 | |
| opt router 192.168.10.2 | |
| @@ -91,8 +62,7 @@ option dns 129.219.13.81 # appened to above DNS servers for a total of 3 | |
| option domain local | |
| option lease 864000 # 10 days of seconds | |
| - | |
| - | # Currently supported options, for more info, see options.c |
| + | # Currently supported options (for more info, see options.c): |
| #opt subnet | |
| #opt timezone | |
| #opt router | |
| @@ -115,9 +85,6 @@ option lease 864000 # 10 days of seconds | |
| #opt tftp | |
| #opt bootfile | |
| - | |
| # Static leases map | |
| #static_lease 00:60:08:11:CE:4E 192.168.0.54 | |
| #static_lease 00:60:08:11:CE:3E 192.168.0.44 | |
| - | |
| - | |